VGuard N series Manual de usuario

VGuard N Series 16/8/4 Channels Embedded Net DVR User’s Manual Please read this user’s manual carefully before you use this system. Please kee

camera displayed will be according to the number of button pressed. Under 16 channels model, to select the enlarge images for camera 9-16, you will re

sub-window location, Save PIP sub-window location.  Leftward Button / Playback Backward 1. Under normal operation: Move selection leftward, Go

 Subtract 1 / Next / Slow Speed Playback 1. Under normal operation: Subtract 1 when setting numbers or next one selection button. 2. Under pl

2.2 System Back Panel: System’s back panel is mainly for signal connection. Detail information as followed:  Power Supply Mark 1: This is for the

14Set order as yellow, black, white and red.  TV Monitor Output BNC-jack Mark 7: TV output BNC-jack to connect to TV monitor.  Audio Input RCA-ja

15disk is over 250GB, system will automatically separate it into 2 or more same partition sizes. Chapter 3 : System Setting This is used to setup th

3.2 Time / Display Setup TIME/DISPLAY SETUP 1.DATE 2006/5/8 2.TIME 18:00:08 3.TIME ZONE GMT+08 4.SYSTE

changing to “On”, or when enlarge one of the camera, this camera will not be enlarge as full screen, instead it will be shown as main screen and other

channel per hour.  Display: Defaulted is on (activate), you can change to off if display not require.  Brightness: Brightness adjustment. Defaulted

19ALARM SETUP : CAMERA1 1.VIDEO LOST CHECK ON 2.MOTION DETECT 9 3.ALARM SOUND OFF 4.ALARM INTERVAL 120 5.MASK1

Declaration： All the specification mentioned in this user’s manual is based on the products when this user’s manual is published. Manufac

20relay output control terminals for selection. This output control terminals is optional. 3.5 System Setup SYSTEM SETUP 1.VIDEO MODE NTSC 2.

 Live Audio: When this is activated, and you had connected audio input to the correspondence cameras, you are able to have live audio monitoring when

in the Internet. Defaulted host name is VGN8C/VGN16C. Users can change the name easier to recognize. You will require setting the “Connect Server” to

23communication ports. Please refer to Chapter 10 Network Connection Setup.  Mode: There are three connection modes. LAN mode, WAN mode and Dail-Up

NETWORK SETUP : CONNECTION 1.LISTEN PORT 50000 50000 2.MODE DIAL-UP 3.USERNAME MANUAL SETUP IP 4.PASSWORD 000

 Primary IP, Secondary IP: User can setup 2 sets of DNS IP.  DDNS Setup VGN4/8C-RT4 system don’t support DDNS function, this setup page would not b

 DOMAIN NAME：Please enter the domain name you applied from DDNS supplier.  USER NAME：Please enter the user name you register with DDNS supplier.

allowed to monitor. Unauthorized camera will not be displayed. From left to right are camera 1/ camera 2/ camera 3/ camera4.  Camera 5-8: This is to

Input/Output setup is to setup the output status and the input’s signal status. Users must setup the output status to correctly control the external d

29condition) and NC (Short under normal condition). Wrong setting will cause error action. When input potential is “---“, it means disable. Input pot

Chapter 1 : System Specification... 6 1.1 System Hardware Specification: ...

303.9 Advanced Setup ADVANCED SETUP 1.STOP RECORD 2.LOGOUT 3.LOGOUT AND RECORD 4.PASSWORD ---------- 5.UPDATE FIRMWARE 6.LOAD DEFAULT 7.FORMAT DVD(

would avoid the error setting by the users, which might cause abnormal operating of the system.  FORMAT DVD(OPT)：This is an optional model. This su

as camera 1-8, a total of 8 image section (VGN8C-RT4).  Status Section: Bottom right hand side is the status section, it display the system time

will be able to see the symbol or whether the recording indicator from the front panel. 4.2 Auto Record If the Auto record is set as ON under system

 Time display: On playback images, recording time and date will be display on the right bottom side of the images for every camera.  Pause: When

13：00：07 14：00：09 5-8 565.0M13：00：07 14：00：09 1-4 718.0M12：00：05 13：00：07 5-8 636.1M12：00：05 13：00：07 1-4 590.2M11：00：06 12：00：05

Chapter 6 : PIP Function PIP functions only support VGA monitor output. This system does not support TV monitor output for PIP function. If user only

If cancel button is pressed after adjustment, then the new location will not be saved. If select/confirm button is press after adjustment, then the n

38detail alarm log: ALARM LOG ： 2006-05-05 13：02：25 CAMERA5 LOSS END 13：00：25 CAMERA5 LOSS START 12：32：35 CAMERA3 MOVE END 12：30：35 CAM

low potential, then the system will triggered the alarm. When input potential is set at low, it means it is low potential under normal condition, you

42.2 System Back Panel: ...13  Power Supply...

1. Use this output control to shut off the alarm sound when alarm triggered. 2. Use up, down buttons to select the outputs and press select button to

41FILE LIST ： 2006-05-03 START END CAMERA LENGTH 14:00:00 15:00:00 1-4 660.0M 14:00:00 15:00:00 5-8 662.3M 13:00:00 14:0

monitoring/recording, it can also connect to other DVR embedded Standalone System , it can also monitoring other PC based images to form a full networ

192.168.1.11:40000 < -------- > 211.172.12.34:40000 This means, the Server IP setting for VGN embedded DVR network setup or Chateau system addre

 VGN Embedded DVR network setup 1. If the recording site (VGN Embedded DVR, and Chateau) is using real IP address for internet (ie.211.175.21

IP 192.168.2.20; Listening Port setting: LAN 50000 WAN 60001 IP 192.168.2.21; Listening Port setting: LAN 50000 WAN 60002 IP 192.168.2.22; Listening P

There are four types for remote: Server; IP, PC DVR and Embedded DVR. In these, Server supports connection from several remote points from PC DVR and

correspondence to this system will display: Press button, if password correct, the following “Remote Channel Select” will be shown as below:

10.3 Remote File Search: Under connected status, click playback button and then click File mode button, you will be able to search for the data

10.4 Remote VGuard N series using IE browser The DVR require to be monitored, which IP address is 192.168.16.107; or the ChateauServer provide with W

53.8 Program...29 3.9 Advanced Setup ...

5. Select “Trusted Sites” 6. Untick “Require Server Verification (http://) for all sites in this zone” 7. Add the IP address that you would like f

9. Enable or prompt “Download Unsigned ActiveX controls”. 10. Select Enable or prompt for “Initialize and Script ActiveX Control not mark as safe” a

 IE Remote DVR 1. If connect directly to the web address for the VGN Embedded DVR, please type in http://192.168.16.107 (The IP address are for dem

then enter the window to input user’s name and password. 2. Please insert the correct username and password. If both are correct, then the following

5. You will be able to remote monitor VGuard N series using Internet Explorer. Images as bellow: The above setting is used when DVR is real IP addr

differences of IP share and Router, please check the user’s manual for your Router and IP share for setup. We would set an example here using ASUS’s B

3. DVR_1 IP address 192.168.1.107, Network communication setting port LAN50000, WAN:60000 (Please setup the IP address using your own network IP add

192.168.1.107:80 < -------- > 111.112.113.114:65000 192.168.1.107:50000 < -------- > 111.112.113.114:60000 192.168.1.108:80 < --------

Chapter 11 : VG Player A VG Player program (V5.4 or later) is included in the CD-ROM we provided. You can playback all the video files Chateau program

11.1 Playback Control Panel: A Playback control panel consists of Basic Functional Control panel and the extended Functional Control Panel. The pi

611.6 Caption Display Setup...62 11.7 VG to AVI Conversion: ...

Zoom Out: You may click the button to reduce an image from its current size by 25%; and click it again to further reduce it by another 25%; and so on

11.2 Search VG Player also support search for VG files by parameter. Under File command, select the file search and the below will show: Firstly you

11.4 Motion Search Setup This function is similar to Chateau’s Motion detection function. You can search for the changing of the picture when playbac

11.7 VG to AVI Conversion: VG Player supports the conversion of VG Files (Includes VG, VGX and VGZ files) to AVI files. The files then can be playba

Click the convert button; a converting window will be pop up. Select the AVI compression format to be converted to proceed with the converting of the

78. Hard Disk: Support 2 IDE Hard disk 9. Backup Function: Supports 2 USB, to connect to USB disks. 10. Ethernet: RJ45 (100/10Mbps Ethernet) 11. Po

8Monitoring and Live Monitoring at the same time. 12. Sensor Input Trigger Alarm 13. Video Lost Trigger Alarm 14. Motion Image Trigger Alarm (maximum

jacks audio connection cables. (Extra audio connection cables are optional). VGN8C-SRT4: 2* BNC jacks video connection cables. 1* RCA jacks audio c